Lhep: 1 revision imported

2015-03-18T07:49:22Z

1 revision imported

New page

Back to [[Bern Bricks]] or [[OPERA]]

===General Informations===

- Brick: 1036423
- Type: CC

- Person: Ciro, Guillaume, Jonas, Tomoko
- Mic: [[Mic1]] -> [[Mic3]]
- SySal Project: MIC3_ST8_collar.prj
- light level: 28900 (update in VertigoScan and PlateChanger)
- FlatField: flatb036423.r8 created
- cutoff 0: 1100
- cutoff 1: 900

- [[Image:Disp_218184565.pdf | Event Display PDF]]
- [http://lheppc46.unibe.ch/EventPictures/Event218184565_vertex.gif Event Viewer]
- [http://141.108.7.20/opitaweb/secure/EventProcess.aspx?evID=82000000000080355 Analysis Follower of the OPERA Experiment]

Muon Informations:
Momentum: 3.364 GeV/c
TX: 0.115
TY: 0.012

=== Predictions ===

automatically extracted by new scannng script and put into pl057

===Loogbook===
Start: 29.07.2008

Follow the [http://lheppc46.unibe.ch/macros/ScanningTutorial/ScanningTutorial.pdf scanning tutorial]

Problems with the new scanning scripts - mail to luca.

tune microscope: load pl57 - tune light, refresh flat field

Install new fedra 852 -> problem solved!

follow script...

part1 - step 4: before load brick, adapt the plate changer status file.

remove the second line when there is one in the bBRICK.map file

Problem with load(FIRST_PLATE) - does not work. stages moves but immediately goes to 2nd / 3rd /... attempt

'''RESTART'''

change ChangerStatus.txt file: brick number must have only the four last digits

continue with part 1 step 3...

remove 4th mark created in the bBRICK.map file (check that only one line)

check light (in middle of top layer)

make test and configure (on top of the plastic base) ... adjust thresholds accordingly (should have 1500-1600 clusters)

measure coners and marks (manual checks):
Top-Right position:
corner_minx = 703
corner_miny = 37
Bottom-Left position:
corner_maxx = 125600
corner_maxy = 99468
1st mark (10000, 10000)
mark1_x = 10632
mark2_y = 10268
2nd mark (10000, 90000)
mark2_x = 10573
mark2_y = 90313
3rd mark (115000, 90000)
mark3_x = 115667
mark3_y = 90524
create_mapfile()

go to part 2...

modify some part of the script (setParamteters... set FragmentSize)

adjust light level (exposure time of camera respectively) and make new flat field

* 30/07/08 afternoon : Add 1 prediction to the official one which seems to be the muon (X=53644, Y=17006, TX=0.104, TY=0.0432)
Try to search predictions on plate 56
But : fedra problem, light problem on MIC1, focus problem (surface damaged)

* 31/07/08 : On MIC1, the light has been changed (light level checked and new flat field made)
Check the Field Threshold Equalization

'''LIGHT UNSTABLE'''

''' RESTART ON MIC3'''

* 04/08/08 : We start from scratch on MIC3

Emulsions are very sticky and the surface are damaged
Some problems to found the optical marks
Sysal crashes very often when "unload current emulsion"

* 05/08/08 : Track with the ID=3 from the CS has not been found on plate 57 BUT near be eyes found a BT (X=53644;Y=17006;TX=0.104; TY=0.0432) --> Modified the pred scan result on plate 57 in order to follow this prediction found by eyes instead of CS pred ID=3.

Some problem to align plate 56 & 57 -> Scan a bigger area 7000.*2*7000.*2 and align with DZ=-1622.92

* 06/08/08 : Prediction found be eyes still alive (plate 21)
Problem with plate 32 : cannot align pl32->pl33 & pl31->pl32
Skip this plate and make align pl31 -> pl33 : No problem

PROBLEM SOLVED : Optical marks are displaced 2 mm in X and 2 mm in Y compared to plate 33 -> Try with Offset=4000. and OK

* 07/08/08 : Alignment problem with plate 8 & 7
-> scan a bigger area 7000.*2*7000.*2. instead of 4000.*2*4000.*2 -> OK

'''Predictions scan stops at plate 5 !'''

* TotalScan from Pl 16 to Pl 4

* 12/08/08 : 1cm2 has been scanned from Pl4 to Pl 57
1 track attached to the vertex (muon) stoppes at plate 56

=== Some PLots ===
[[Image:vertex_b036423.png]]

== ScanForth ==

TotalScan 1cm2 done from Pl5 to Pl57 (id=1000, version=3)

Vextex has 5 prong :

* One track stoppes at Plate 56 -> '''Muon''' ScanForth (id=600) found a BT on plate 57 :
Path 1: Prediction: 53566.257812 16908.371094 0.108700 0.025217
Status 0: BT found
BT : 53545.1 16901.5 0.1420 0.0219 21 1.5564 0.000000
Res: -21.1 -6.9 0.0333 -0.0034
MT1: 53560.3 16903.8 0.0212 -0.0135 11 2.8266 0.000000
Res: -5.9 -4.5 -0.0875 -0.0387
MT2: 53529.9 16899.2 0.0158 -0.0021 10 2.9547 0.000000
Res: -36.3 -9.2 -0.0929 -0.0273
Preliminary (BT,MT1,MT2) = (1,1,4)
Candidates (BT,MT1,MT2) = (1,0,0)
'''Manual check : not confirmed'''

* One track stoppes at Plate 31 -> ScanForth (id=300) from Pl 31 to Pl 35 confirms stop at Plate 31
* One track stoppes at Plate 24 -> ScanForth (id=300) from Pl 24 to Pl 30 confirms stop at Plate 24
* One track stoppes at Plate 14 -> ScanForth (id=400) from Pl 14 to Pl 18 confirms stop at Plate 14
* One track stoppes at Plate 13 -> ScanForth (id=500) from Pl 13 to Pl 17 confirms stop at Plate 13

== DB Publication ==

* 13/08/08 : Bern DB publication IDPROCESS=5000000001310004

Calibrations starts at 11h12

Error in <TOracleServerE2W::TOracleServerE2W>: AddView; failed: (error: ORA-01683: unable to extend index
OPERA.PK_MIPMICROTRACKS partition P_BE01 by 8192 in tablespace OPERASCAN_BE01)

TO DO:
ORA-01683: unable to extend index string.string partition string by string in tablespace string
Cause: Failed to allocate an extent of the required number of blocks for index segment in the tablespace indicated.
Action: Use ALTER TABLESPACE ADD DATAFILE statement to add one or more files to the tablespace indicated.

root [5] DeleteOperation("5000000001310004")
DeleteOperation started
DeleteOperation completed
Elapsed time = 2957 seconds

=== Central DB communications===

===Problems===

0) Debug the new scanning script :-)

1) Very very very sticky emulsions

2) Surface damaged : Emulsions were not dry enough (after 2.5 days drying @ Gran Sasso) and damaged done by separator

3) Light unstable on MIC1 --> use MIC3

4) Some problems to found the optical marks on MIC3

5) Sysal (maybe due to the stage) crashes when "Unload current emulsion" on MIC3
but no problem if plate is unloaded with the scanning script

6) Problem to align Plate 56 to 57
Succeed by increasing the intercalibration area and with a DZ=-1622.92

7) On Plate 32 optical marks are shifted (~2mm in X and ~2 mm in Y) compared to plate 33

1036423 - Revision history

Lhep: 1 revision imported